Menu
Your Cart

POLISHER 1200W WOOL BONNET 180MM WITH 4M CORD 6 MONTHS WARRANTY

POLISHER 1200W WOOL BONNET 180MM WITH 4M CORD 6 MONTHS WARRANTY
POLISHER 1200W WOOL BONNET 180MM WITH 4M CORD 6 MONTHS WARRANTY
Based on 0 reviews. - Write a review
Price
R 2,309.49
Ex VAT: R 2,008.25
  • Stock: In Stock
  • Cat No: POL02
  • Weight: 3.26kg
  • Dimensions: 142.00mm x 450.00mm x 450.00mm
  • SKU: POL02
  • Barcode: 6009515828516
  • Pack Size: 6

Available Options

Ask Question Ask Question
Stockists
Polisher

Wattage: 1200W
No load speed: 1100-3500 RPM

Supplied with a ø180mm wool bonnet buff and backing pad.

Application:

The polisher is a power tool used in the finishing process, used with polishing buffs and compound sponges to yield a dramatic difference on a painted surface.

The objective of polishing is to remove imperfections in the clear-coat that cause the paint to look dull. Surface imperfections can include swirls, scratches, water spots, etchings, industrial fallout, oxidation, etc.

Features:

  • Professionally manufactured for the automotive paint care and detailing industries.
  • Ergonomically designed to reduce fatigue in long term use.
  • The polisher has various hand-held positions to better hold the polisher at angles.
  • Gear system has a two-level deduction. With two times the amount of torque than a single gear set polisher.

The polisher range:

ORDER NO. DESCRIPTION WARRANTY
POL01 Polisher, 800W. Supplied with ø125mm wool buff 6 Months
POL02 Polisher, 1200W. Supplied with ø180mm wool buff 6 Months
POL03 Polisher, 1700W. Supplied with ø180mm sponge pad 6 Months

 

The Tork Craft polisher features a built-in variable speed control. It is advisable to use the polisher on it's lowest speed to prevent friction. Lift the polisher often away from the panel (under no-load) to allow the motor to cool down.

Spare parts for the POL02 polisher:

ORDER NO. DESCRIPTION
POL02-12 Big gear
POL02-13 Bearing
POL02-16 Aluminium head
POL02-19 Fixation knob
POL02-24 Armature
POL02-29 Field coil (stator)
POL02-30 Motor housing
POL02-33 Carbon brushes
POL02-37-38 Speed control (switch)
POL02-40 Rear handle
POL02-46 Trigger switch
Polisher

Steps to take when polishing a panel:

1. Preparing the panel:

  • Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
  • The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
  • Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.

2. Applying the polishing compound:

  • A five rand coin amount of polishing compound should be applied to the buff. Switch the polisher to it's lowest speed setting.
  • Switch on the polisher and gradually spread the polishing compound over the panel.
  • Keep moving the polisher on the panel to have as little amount of pressure and friction.
  • The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
  • Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.

3. Wash the panel when finished:

  • Wash the panel after polishing to remove any residue from the polishing compound.
consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

 

Download the Exploded view:
Download PDF File
View the Exploded view:
View PDF File

 

Download the Specification sheet:
Download PDF File
View the Specification sheet:
View PDF File
Tags: Polisher , Power tools , Brand TORK CRAFT